飞机舱门锁机构多失效模式可靠性分析方法

如何提高飞机舱门锁机构关闭系统的可靠性计算效率,减少计算时间,降低舱门故障率是亟待解决的 问题。选取某型飞机舱门锁机构为研究对象,通过 LMS建立飞机舱门锁机构仿真模型,研究锁机构关闭过程 中最大液压力失效和关锁时间失效模式的影响因素,考虑两种失效模式之间的相关性,基于重要抽样法和 B-P 神经网络方法,计算飞机舱门锁机构多失效模式下的可靠性;将这两种方法仿真计算结果与传统蒙特卡罗方法 计算结果进行对比,结果表明:以上两种计算飞机舱门锁机构可靠性的方法是合理的,其误差范围均在3%以 内,且两种方法的计算效率相较于传统方法均有所提高;其中,B-P神经网络方法比重要抽样法计算精度和效 率更高,更适用于研究飞机舱门锁机构的可靠性问题。     

地面系留对直升机动力响应的影响

 建立了系留状态下直升机旋翼/机体耦合非线性动力学模型,无铰旋翼简化为当量铰刚性桨叶模型,假定机体是刚性体并受起落架和系留索的约束,系留索静态时松弛并只能承受拉力。采用数值仿真研究了系留对模型旋翼地面共振的影响,对初始扰动和旋翼转速对系统动力学行为的影响也进行了仿真研究。对于无系留的模型旋翼来说,在任何转速下没有出现不稳定现象;地面系留时系统会呈现稳定响应、极限环以及大幅值振荡等非线性动力学行为,大幅值振荡将使系留索、接头和支持结构承受破坏性动力载荷。     

Nonlinear Dynamics Behaviors of a Rotor Roller Bearing System with Radial Clearances and Waviness Considered

A rotor system supported by roller beatings displays very complicated nonlinear behaviors due to nonlinear Hertzian contact forces, radial clearances and bearing waviness. This paper presents nonlinear bearing forces of a roller bearing under four-dimensional loads and establishes 4-DOF dynamics equations of a rotor roller bearing system. The methods of Newmark-β and of Newton-Laphson are used to solve the nonlinear equations. The dynamics behaviors of a rigid rotor system are studied through the bifurcation, the Poincar è maps, the spectrum diagrams and the axis orbit of responses of the system. The results show that the system is liable to undergo instability caused by the quasi-periodic bifurcation, the periodic-doubling bifurcation and chaos routes as the rotational speed increases. Clearances, outer race waviness, inner race waviness, roller waviness, damping, radial forces and unbalanced forces-all these bring a significant influence to bear on the system stability. As the clearance increases, the dynamics behaviors become complicated with the number and the scale of instable regions becoming larger. The vibration frequencies induced by the roller bearing waviness and the orders of the waviness might cause severe vibrations. The system is able to eliminate non-periodic vibration by reasonable choice and optimization of the parameters.     

Foreign Object Damage to Fan Rotor Blades of Aeroengine Part Ⅱ： Numerical Simulation of Bird Impact

Bird impact is one of the most dangerous threats to flight safety. The consequences of bird impact can be severe and, therefore, the aircraft components have to be certified for a proven level of bird impact resistance before being put into service. The fan rotor blades of aeroengine are the components being easily impacted by birds. It is necessary to ensure that the fan rotor blades should have adequate resistance against the bird impact, to reduce the flying accidents caused by bird impacts. Using the contacting-impacting algorithm, the numerical simulation is carded out to simulate bird impact. A three-blade computational model is set up for the fan rotor blade having shrouds. The transient response curves of the points corresponding to measured points in experiments, displacements and equivalent stresses on the blades are obtained during the simulation. From the comparison of the transient response curves obtained from numerical simulation with that obtained from experiments, it can be found that the variations in measured points and the corresponding points of simulation are basically the same. The deforming process, the maximum displacements and the maximum equivalent stresses on blades are analyzed. The numerical simulation verifies and complements the experiment results.     

TC4钛合金腐蚀加工速度和表面质量影响因素研究

研究了腐蚀溶液成分和工艺参数对TC4钛合金腐蚀加工速度、表面粗糙度和平整度的影响,利用扫描电镜观察了腐蚀加工前后的表面形貌.研究结果表明:氢氟酸浓度和溶液温度直接决定着腐蚀加工速度,随HF浓度和温度的增加,腐蚀加工速度升高.硝酸具有显著降低表面粗糙度的作用.溶液中的钛离子对腐蚀加工速度以及钛合金零件腐蚀后的表面质量有一定的影响,溶液中钛离子含量较低时,腐蚀加工速度较快,表面平整度较好,随钛离子含量的增加,腐蚀加工速度下降,表面不平整度增加.试样垂直吊挂时,定时翻转并搅拌可以得到均匀腐蚀的表面.     

2.5维机织复合材料纬向拉伸过程初始屈服准则

2.5维机织复合材料已有较为广泛的应用,而目前对该类复合材料的破坏机理和失效原因尚未形成统一的认识。根据三维机织复合材料的拉伸试验现象,基于经纱曲面层板纬向纤维和树脂应力相等的假设,建立了2.5维机织结构复合材料纬向拉伸过程的初始屈服条件和屈服准则。通过对2.5维机织复合材料3种结构12个试件进行纬向拉伸试验及文献中的三维机织复合材料拉伸试验,与计算预测结果的对比表明本文中建立的初始屈服准则的合理性。研究表明,树脂横向裂纹是2.5维结构复合材料纬向拉伸过程初始屈服产生的直接原因;2.5维机织复合材料出现纬向拉伸屈服的条件仅和经纱曲面板内的经纱体积含量、纤维和基体的弹性模量及基体的拉伸破坏强度等因素有关,而与经纱曲面板的走向和层数无关。因为组分弹性模量不同,在纬向拉伸过程中,树脂应变高于复合材料的应变。树脂的初始横向裂纹首先发生在纤维密集处,并向富树脂区扩展;裂纹在向纤维方向扩展过程中受到纤维的阻碍而受到限制。     

温度场中柔性臂超谐共振及复杂运动分析

通过Garlerkin方法建立了考虑阻尼、材料非线性、温度变化和轴向激励的柔性臂系统动力学微分方程.分析了系统存在同、异宿轨道及周期轨道的充分必要条件,通过Hamilton函数得到了对应的参数方程表达式.根据非线性振动的多尺度法,得到了系统在3次超谐共振情况下的一次近似解及其定常解,揭示了系统内各参数之间的关系.对得到的微分方程进行数值计算,分析柔性臂系统参数对纵向振动响应曲线的影响.结果表明,材料非线性和温度变化对系统纵向振动的影响不可忽略;在一定参数条件下,系统有发生复杂非线性运动的可能.为了有效的控制柔性臂的振动,应合理选取系统的物理参数,避免其处于混沌运动状态.     

战斗部中火工品装配技术研究

介绍了战斗部用火工品的分类、组成和原理,论述了各种火工品在战斗部中装配的安全要素,装配过程中发生的主要故障,以及故障处理和预防。工程应用表明采取安全技术措施和故障处理技术,杜绝了火工品装配引起的安全问题,产品的故障率大幅度下降。     

基于SPWD多载波频率估计算法的改进

针对目前提出的多载波估计算法存在的速度与精度的问题,基于模糊控制理论,改进和完善了多载波信号载频估计算法.通过对多载波时隙ALOHA网络真实卫星信号的载频频点提取,验证了该改进算法的时效性.     

双密封结构的泄漏理论及其应用研究

建立了双密封结构系统的数学模型 ,通过理论分析和数值计算 ,揭示了双密封结构系统正压泄漏的漏率、漏量与泄漏时间关系的规律及其影响因素的结论。这些研究结果可用于双密封结构系统的设计、检漏和泄漏安全评估 ,以理论指导实践。